|
|
|
|
|
|
| |
DN-8468 Series
Photo-isolated terminal boards for ICP DAS four-axis stepper/servo controller |
|
| |
 |
|
| |
|
|
| |
| |
|
|
| |
DN-8468UB
Universal Snap-on wiring terminal board |
 |
| |
 |
|
|
| |
|
|
| |
DN-8468GB
General purpose wiring terminal board |
|
| |
 |
|
|
| |
|
|
| |
DN-8468MB
Snap-on wiring terminal board for Mitsubishi MELSERVO-J2 servo amplifier |
|
| |
 |
|
|
| |
|
|
| |
DN-8468PB
Snap-on wiring terminal board for Panasonic MINAS A4/A5 servo amplifier |
|
| |
 |
|
|
| |
|
|
| |
DN-8468YB
Snap-on wiring terminal board for Yaskawa Sigma II/III/V servo amplifier |
|
| |
|
|
|
| |
|
|
| |
DN-8468DB
Snap-on wiring terminal board for Delta ASDA-A servo amplifier |
|
| |
|
|
|
| |
|
|
| |
DN-8468FB
Snap-on wiring terminal board for Fuji FALDIC-W servo amplifier |
|
| |
 |
|
|
|
|
|
| |
|
|
| |
 |
|
| |
|
|
|
 |
|
|
|
|
|
The
DN-8468 series is a daughter-board that is designed for ICP DAS’s 4-axis
motion
controllers, such as I-8094,I-8094F, I-8094A, I-8094H, and PISO-PS400.
And they are for different motor drivers, such as general purpose
usage, Mitsubishi and Panasonic motor amplifier. It is a not only a
screw terminal board for easy connection of signals; it also provides
onboard isolating circuitry to protect the controllers. Interface
signals are divided into four groups. Each group corresponds to a
single axis and contains the necessary pulse output command lines,
encoder feedback lines, special purpose inputs (Home, near home, limit-switches) and a servo-enable output. Terminal connectors are used for
easy wiring purpose. Users can interchange connectors to interchange
each axial definition without laborious rewiring. This board also
contains onboard power module which provides different voltages for
other onboard circuitry. And this power module accepts wide range input
power (12 ~ 30 VDC). |
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
- High Speed Photo-coupling
Isolated.
- Supporting Pulse Command Type
Step Motors or Servo Motors.
- Providing Power LED and Other
Status LEDs (Home, Limit Switches, …)
- Providing FRnet Terminal for
High-speed Serial I/O Expansion when the Controller Supports FRnet.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
| Power |
| Nominal Load |
0.5
A /24 VDC |
| Input Power |
12 ~ 30 VDC, 0.5 A |
| Power Consumption |
12 W (24 VDC) |
| Environment |
| Operating
Temperature |
-20 ~ +75 °C |
| Storage
Temperature |
-30 ~ +85 °C |
| Operating Humidity |
20 ~ 80% RH, Non-condensing |
| Storage Humidity |
10 ~ 90% RH, Non-condensing |
| Dimensions |
| 162 mm X 107 mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
| DN-8468UB |
| CA-26-MJ3-15/30/50 |
HD DSub 26-pin Male cable for Mitsubishi servo amplifier, 1.5/3/5 M (for MELSERVO-J3/J4 series) |
| CA-26-YSV-15/30/50 |
HD DSub 26-pin Male cable for Yaskawa servo amplifier, 1.5/3/5 M (for Sigma II/III/V series) |
| CA-26-PA4-15/30/50 |
HD DSub 26-pin Male cable for Panasonic servo amplifier, 1.5/3/5 M (for MINAS A4/A5 series) |
| CA-26-DAA2-15/30/50 |
HD DSub 26-pin Male cable for Delta A2 servo amplifier, 1.5/3/5 M (for ASDA-A2 series) |
| CA-26-DAB2-15/30/50 |
HD DSub 26-pin Male cable for Delta B2 servo amplifier, 1.5/3/5 M (for ASDA-B2 series) |
| CA-26-FFW-15/30/50 |
HD DSub 26-pin Male cable for Fuji servo amplifier, 1.5/3/5 M (for FALDIC-W and ALPHA5 Smart series) |
| CA-26-TTA-15/30/50 |
HD DSub 26-pin Male cable for Teco servo amplifier, 1.5/3/5 M (for TSTA-A/A+ series) |
| DN-8468DB |
| CA-SCSI50-D1/3/5 |
SCSI II 50-pin & 50-pin Male connector cable 1/3/5 M (for ASDA A series) |
| DN-8468YB & DN-8468PB |
| CA-SCSI50-PY1/3/5 |
SCSI II 50-pin & 50-pin Male connector cable 1/3/5 M (for Panasonic & Yaskawa series motor) |
|
|
|
|
|
|
|
|
|
|
|
|